From basic Swing Check Valves to RPZ Valves, we have a everything you need when it comes to back flow prevention. If you're not sure what you're after, when installing an irrigation system, most regulations require a minimum Dual Check Valve to protect contamination of the mains water supply.
Use the Dual Check Valve for backflow prevention from your irrigation system to the mains water supply.They are a mandatory requirement and should be fitted on all irrigation systems that are connected to the mains because Dual Check Valves effectively prevent the backflow of potentially harmful debris.Be aware that a regular Spring Ch..
Protect your family and community's water supply by installing one of our tap water connection kits. This kit contains everything you need to bypass your garden tap, and have a stand alone outlet for your irrigation system. Both options below provide the absolute minimum connections possible, this will see less leaking potential, and greater flo..
Attach this backflow device to your tap to prevent backflow.These Hose Bib Check Valves are designed for use on drip system because they also have a Vacuum Breaker Valve to ease the pressure on the drip tube system.If you are unsure of the size of the valve you need, please see this link: How to measure BSP threads and PVC Pipe..
Use the Spring loaded check valve for tank systems to prevent backflow contamination.These spring loaded check valves don't provide enough protection to be able to prevent backflow to mains water but they are perfect for tank systems that are linked with mains water.Install a spring loaded check valve on a tank/mains system to prevent mains water f..
Use the Swing check valve for tank systems to prevent backflow contamination.These swing check valves don't provide enough protection to be able to prevent backflow to mains water but they are perfect for tank systems that are linked with mains water.Install a swing check valve on a tank/mains system to prevent mains water filling up y..
The double check flow is a testable backflow device.Protect your system from contamination with this double check valve, flush out the valve without spreading contaminants throughout your pipeline.They are a mandatory requirement and should be fitted on all irrigation systems that are connected to the mains on a public site. eg. schools, football f..
Designed for installation on pressure water systems, it protects against both back-siphonage and back-pressure of contaminated water into the water supply.Use of the RPZ valve shall provide protection where a health hazard exists. They are a mandatory requirement and should be fitted on all irrigation systems that are connected to the mains with a ..
Are there any safety standards my irrigation system must meet?
The main safety concern is regarding the water supply. To avoid contamination of the mains water upstream, in most municipalities, a Dual Check Valve is required at the water connection.
Do I need to use teflon tape? How much do I need to use?
Whenever you’re connecting two threaded fittings, teflon is required. The only exception is whenever either fitting has an O-ring, in this case, do not apply teflon as it may cause the O-ring to not seal correctly. The amount of teflon you apply depends on the application. In any constant pressure applications you look at up to wrapping around the thread up to 20 times, whereas in any non-constant pressure applications, like on irrigation risers, 2 or 3 times around the thread is enough.
How deep do I need to bury my pipe?
There’s no requirement to bury irrigation pipes any depth, but there are a couple of things to consider; Allow enough room to run the pipe under your sprinklers so they sit at the right height & think about going deeper to avoid damage in areas where future digging or planting might happen. 20-30cm is often deep enough.
What size pipe do I need to use?
Pipe sizing is all about reducing friction loss & allowing maximum flow to all points of your garden. There are a number of variables to consider, but in most domestic applications, 19mm Poly Pipe is the common choice. In larger areas, where you may have to run pipe 30-40m to the start of an irrigation zone, or zones with large sprinklers with high flow requirements, you may want to consider upping your pipe size to 25mm of more boost that flow output.
What type of pipe should I use on my irrigation system?
The type of pipe you use depends on the water pressure of the application. For example, in any application under constant mains pressure like before your Irrigation Valves, you’ll need pipe that can cope. This rules out Low Density Poly Pipe & you’ll need to use something like Class 12 PVC or Metric Poly Pipe, these typically have a rating of Class 12, or PN12 which translates to being able to cope with 1200kPa. For irrigation lines after the valves in most domestic applications, Low Density Poly Pipe is ideal. In this situation, the operating pressure is much lower because the water is able to escape out of the operating sprinklers or drip tube & once the valves shut off, there is no static pressure build up.
Why should I buy from an Australian website?
We get any number of calls from people across the country who've bought from overseas & have problems. From electrical output problems to thread compatibility problems & other problems that we aren't able to help with!
By buying from SunshowerOnline, right here in Australia, you can be sure that your warranty issues are covered, that compatibility & compliance isn't an issue & that you'll be able to get helpful after service advice.
