50mm DWV PVC

50mm DWV PVC

Drainage, Waste and Vent (DWV) fittings for use with DWV pipe in non-pressure applications such as sewer water.

Show:
Sort By:
PVC DWV Coupling 50mm
$3.72 $4.09 Ex Tax: $3.72

PVC DWV Coupling 50mm

This straight Coupling is for sewer and vent use and connects to pipe with solvent cement. It complies with AS/NZS1260.These fittings are sized specifically for use with 50mm Pipe and fittings, it is deliberately sized differently to pressure pipe so there is no risk of cross contamination between water sources...

PVC DWV Elbow 88° 50mm
$5.52 $6.07 Ex Tax: $5.52

PVC DWV Elbow 88° 50mm

This Plain bend is for sewer & vent use. Connect pipe with solvent cement. Complies with AS/NZS1260. (Drain Waste Vent) systems remove waste water from showers, sinks, toilets and floor drains.These fittings are sized specifically for use with 50mm Pipe and fittings, it is deliberately sized differently to pressure pipe so there is..

PVC DWV Elbow 45° 50mm
$6.18 $6.80 Ex Tax: $6.18

PVC DWV Elbow 45° 50mm

This plain bend is for sewer & vent use. Connect pipe with solvent cement. Complies with AS/NZS1260. (Drain Waste Vent) systems remove waste water from showers, sinks, toilets and floor drains.These fittings are sized specifically for use with 50mm Pipe and fittings, it is deliberately sized differently to pressure pipe so there is no risk..

PVC DWV F.I. Adaptor 50mm
$8.20 $9.02 Ex Tax: $8.20

PVC DWV F.I. Adaptor 50mm

This female threaded adaptor is for sewer and vent use and connects to pipes with solvent cement. It complies with AS/NZS1260.*Spigot same OD as pipe, fits into another fitting...

PVC DWV M.I. Adaptor 50mm
$8.20 $9.02 Ex Tax: $8.20

PVC DWV M.I. Adaptor 50mm

This female threaded adaptor is for sewer and vent use and connects to pipes with solvent cement. It complies with AS/NZS1260.*Spigot same OD as pipe, fits into another fitting.These fittings are sized specifically for use with 50mm Pipe and fittings, it is deliberately sized differently to pressure pipe so there is no risk of cross contaminat..

PVC DWV Elbow 88° M&F 50mm
$13.02 $14.33 Ex Tax: $13.02

PVC DWV Elbow 88° M&F 50mm

Use this DWV 88° M & F Elbow to change the direction and put a bend in a 50mm DWV pipe. The Male end slips into a DWV fitting and the Female end slips onto the pipe. Use these fittings to connect grey water systems.These fittings are sized specifically for use with 50mm Pipe and fittings, it is deliberately sized differently to pressure..

PVC DWV Elbow 42° M&F 50mm
$13.96 $15.36 Ex Tax: $13.96

PVC DWV Elbow 42° M&F 50mm

Use this DWV 42° M & F Elbow to change the direction and put a bend in a 50mm DWV pipe. The Male end slips into a DWV fitting and the Female end slips onto the pipe. Use these fittings to connect grey water systems.These fittings are sized specifically for use with 50mm Pipe and fittings, it is deliberately sized differently to pressure..

PVC DWV Junction 45° 50mm
$27.58 $55.16 Ex Tax: $27.58

PVC DWV Junction 45° 50mm

Use this DWV 45° Junction to change the divert a 50mm DWV pipe off an existing pipeline. Use these fittings to connect grey water systems.  Connect pipe with solvent cement. Manufactured to Australian Standards.These fittings are sized specifically for use with 50mm Pipe and fittings, it is deliberately sized differently to pressure pi..

PVC DWV Junction 88° 50mm
$28.28 $31.11 Ex Tax: $28.28

PVC DWV Junction 88° 50mm

Use this DWV 88° Junction to change the divert a 50mm DWV pipe off an existing pipeline. Use these fittings to connect grey water systems. Connect pipe with solvent cement. Manufactured to Australian StandardsThese fittings are sized specifically for use with 50mm Pipe and fittings, it is deliberately sized differently to pressure pipe..

Need Help with 50mm DWV PVC?

50mm DWV PVC FAQs

50mm DWV PVC FAQs
  • The main safety concern is regarding the water supply. To avoid contamination of the mains water upstream, in most municipalities, a Dual Check Valve is required at the water connection.

  • Whenever you’re connecting two threaded fittings, teflon is required. The only exception is whenever either fitting has an O-ring, in this case, do not apply teflon as it may cause the O-ring to not seal correctly. The amount of teflon you apply depends on the application. In any constant pressure applications you look at up to wrapping around the thread up to 20 times, whereas in any non-constant pressure applications, like on irrigation risers, 2 or 3 times around the thread is enough.

  • There’s no requirement to bury irrigation pipes any depth, but there are a couple of things to consider; Allow enough room to run the pipe under your sprinklers so they sit at the right height & think about going deeper to avoid damage in areas where future digging or planting might happen. 20-30cm is often deep enough.

  • Pipe sizing is all about reducing friction loss & allowing maximum flow to all points of your garden. There are a number of variables to consider, but in most domestic applications, 19mm Poly Pipe is the common choice. In larger areas, where you may have to run pipe 30-40m to the start of an irrigation zone, or zones with large sprinklers with high flow requirements, you may want to consider upping your pipe size to 25mm of more boost that flow output.

  • The type of pipe you use depends on the water pressure of the application. For example, in any application under constant mains pressure like before your Irrigation Valves, you’ll need pipe that can cope. This rules out Low Density Poly Pipe & you’ll need to use something like Class 12 PVC or Metric Poly Pipe, these typically have a rating of Class 12, or PN12 which translates to being able to cope with 1200kPa. For irrigation lines after the valves in most domestic applications, Low Density Poly Pipe is ideal. In this situation, the operating pressure is much lower because the water is able to escape out of the operating sprinklers or drip tube & once the valves shut off, there is no static pressure build up.

  • We get any number of calls from people across the country who've bought from overseas & have problems. From electrical output problems to thread compatibility problems & other problems that we aren't able to help with!

    By buying from SunshowerOnline, right here in Australia, you can be sure that your warranty issues are covered, that compatibility & compliance isn't an issue & that you'll be able to get helpful after service advice. 

View More View All FAQs