Hunter Pro-Spray PRS40 Pop-Up Sprinklers

Hunter Pro-Spray PRS40 Pop-Up Sprinklers

Hunter’s revolutionary MP Rotator technology and water savings is brought to life in the PRS40. The great features of the PRS40 combine the rugged Pro-Spray body and the efficiency of the MP Rotator.

MP Rotators use multi-stream technology to deliver precise streams of water with superior uniformity. When used in place of standard spray nozzles, it’s not uncommon to see system water use decrease by up to 30% or more.  Regulated at 2.8 bar; 280 kPa the Pro-Spray PRS40 ensures the optimum output pressure to achieve maximum efficiency. It is recommended for both residential and commercial applications, and is available in an array of configurations to suit the needs of any site.


Note: Sprinkler sizing relates to pop-up height, not overall body size.

    100mm Hunter Pro-Spray PRS40 Pop-Up150mm Hunter Pro-Spray PRS40 Pop-Up300mm Hunter Pro-Spray PRS40 Pop-Up
    Specs
    Type Pop-Up Body Pop-Up Body Pop-Up Body
    Material Plastic Plastic Plastic
    Colour Black, Grey Black, Grey Black, Grey
    Inlet Thread Size 15mm BSPF 15mm BSPF 15mm BSPF
    Outlet Thread Size 10mm Male Thread 10mm Male Thread 10mm Male Thread
    Min. Recommended Pressure (kPa) 100 100 100
    Max. Recommended Pressure (kPa) 700 700 700
    Max. Pressure Output (kPa) 280 280 280
    Pop-Up Height 100mm 150mm 300mm
    Extra Features Pressure Regulated, Check Valve Pressure Regulated, Check Valve Pressure Regulated, Check Valve
    • The main safety concern is regarding the water supply. To avoid contamination of the mains water upstream, in most municipalities, a Dual Check Valve is required at the water connection.

    • We definitely don’t recommend it. Typically, drip tube will deliver the water at a far slower rate that sprays. Because of this, if you were to have both on the same zone, the areas with drip would be left far drier than the areas with sprinkler coverage. If you do want to water some areas with drip & some with sprinklers, it can be done, but each will just need to be run on their own separate irrigation zones.

    • A garden tap is an excellent place to connect your irrigation system. Ideally, install a connection point behind the tap (turn the water off first) so you can still use your tap to fill a bucket when you need to.

    • Even on a typical domestic system running on mains water a filter is still a good idea. In the event of a water main fault where rubbish does find it’s way down the line, a filter will protect the system from blockage and or failure. On systems operating off recycled water, like from a tank, a screen filter is mandatory. Debris like silt & dirt from recycled water is the most common cause of blockages of failures in irrigation systems.

    • No, unless you’re tapping into your water supply, a plumber isn’t required. Most domestic irrigation systems can be installed by anyone half handy.

    • Firstly, each sprinkler &/or nozzle has a specified spray radius. Secondly, sprinklers are typically designed to deliver more water at their base & progressively less the further away you get. For this reason, you want to position sprinklers so they spray to hit the base of the next sprinkler. Of course this isn’t possible all the time so in those cases, aim to spray at least 80% of the way. By doing this you will guarantee even water across your lawn or garden.

    • Each sprinkler & nozzle sprays water at different rates, but the key factor is the flow rate of your water supply. Work that out with a simple timed bucket test. From there, you can work out how much water each sprinkler you’re looking at uses & work within your flow limit. For more information, check our Product Guides.

    • Well you’re in the right place! We’ve got it all here. The first step, is drawing out a plan of your garden, to scale of course. We’ve got Grid Paper in our Product Guides & all the advice you’ll need in there too!

    • As you install a system, it’s almost inevitable that small fragments of dirt will get into the pipe, for this reason you should always flush out the system before running it the first time. This can be done by leaving an open end at the farthest point of each irrigation zone & operating the zone for 15 or so seconds to flush it out. Then plug it up & you’re good to go! This can also be said for any other times dirt may have gotten into the system (eg: further irrigation repairs or a mains water supply fault).

    • The type of nozzle all depends on how far you need to spray, each nozzle is specified by the radius it sprays & the spray arc it provides (0-360 degrees). Aim to spray to the base of the next closest sprinkler for even watering. For more information on planning, check out our Product Guides.

    • There’s no best type of sprinkler, just better sprinklers for different applications. Gear Drives are better for large areas, over 5m. Pop-Ups are ideal for 1.5-5m & Micro sprays are excellent for anything under that.

    • We get any number of calls from people across the country who've bought from overseas & have problems. From electrical output problems to thread compatibility problems & other problems that we aren't able to help with!

      By buying from SunshowerOnline, right here in Australia, you can be sure that your warranty issues are covered, that compatibility & compliance isn't an issue & that you'll be able to get helpful after service advice. 

    Write a review

    Please login or register to review
    • $12.63
      $17.77
      $12.63 $17.77 Ex Tax: $12.63
      • SKU: ISP-HUNPRS40100
      • Brand: Hunter
      • MPN: PROS-04-PRS40-CV
      • Availability: In Stock
      • Warranty: 5 year
    • $33.08
      $37.46
      $33.08 $37.46 Ex Tax: $33.08
      • SKU: ISP-HUNPRS40150
      • Brand: Hunter
      • MPN: PROS-06-PRS40-CV
      • Availability: In Stock
      • Warranty: 5 year
    • $37.95
      $44.66
      $37.95 $44.66 Ex Tax: $37.95
      • SKU: ISP-HUNPRS40300
      • Brand: Hunter
      • MPN: PROS-12-PRS40-CV
      • Availability: Ships in 1-3 Days
      • Warranty: 5 year