Vyrsa 26 Full Circle Plastic Impact Sprinklers

Vyrsa 26 Full Circle Plastic Impact Sprinklers

The VYR-26 is a low flow sprayer specially designed to operate at different angles and under extreme temperature conditions. Its axis and springs are made of stainless steel, O-rings  and washers in stainless steel, Teflon and special poly-carbonate to withstand contact with fertilizers more aggressive in the market.

The wide range of plastic nozzles with different colors for easy differentiation,  offer a number of possible combinations. This sprinkler  is designed to work under flow ranges  between 168  and 1450 L/H, at pressures  between 1 and  3.5 bar,  with a  coverage range between 21-24m diameter.  The VYR-26 can work with one or two nozzles;  The main nozzle has 26° inclination to the horizontal plane  and the secondary  18º.  Average rotation time is approximately 40  sec/rot. 

For optimum  uniformity, it's recommend using these sprinklers with a spacing between sprinkler heads at 10m apart in a rectangular formation, or 12m apart in a triangular formation.

The most common use is for grains such as  wheat, barley or corn, alfalfa, beets,  leafy robust, legumes  and tubers.

  • 15mm BSP male inlet
  • Radius coverage: 10.5 - 12m
  • Flow range: 240 - 860 lph 
  • 26º trajectory (main), 18º trajectory (secondary)
  • Stainless steel spring & axle
  • Individual nozzles available here: Vyrsa 26 Plastic Impact Nozzles




    • Vyrsa 26 Plastic Impact Sprinkler (Body Only)Vyrsa 26 Plastic Impact Sprinkler (2.5mm x 2.5mm Dual Nozzle)Vyrsa 26 Plastic Impact Sprinkler (2.8mm x 2.5mm Dual Nozzle)Vyrsa 26 Plastic Impact Sprinkler (3.0mm x 2.5mm Dual Nozzle)Vyrsa 26 Plastic Impact Sprinkler (3.2mm x 2.5mm Dual Nozzle)
      Specs
      Type Full Circle Impact Sprinkler Body Full Circle Impact Sprinkler Full Circle Impact Sprinkler Full Circle Impact Sprinkler Full Circle Impact Sprinkler
      Material Plastic Plastic Plastic Plastic Plastic
      Colour Black Black Black Black Black
      Inlet Thread Size 15mm BSPM 15mm BSPM 15mm BSPM 15mm BSPM 15mm BSPM
      Min. Flow Output (Lpm) 4.95 5.9 6.8 10.8
      Max. Flow Output (Lpm) 6.9 7.6 8.5 14.3
      Min. Recommended Pressure (kPa) 250 250 250 250
      Max. Recommended Pressure (kPa) 350 350 350 350 350
      Min. Spray Radius (m) 11.4 11.8 11.8 12.8
      Max. Spray Radius (m) 11.7 12.0 12.5 13.0
      • The main safety concern is regarding the water supply. To avoid contamination of the mains water upstream, in most municipalities, a Dual Check Valve is required at the water connection.

      • We definitely don’t recommend it. Typically, drip tube will deliver the water at a far slower rate that sprays. Because of this, if you were to have both on the same zone, the areas with drip would be left far drier than the areas with sprinkler coverage. If you do want to water some areas with drip & some with sprinklers, it can be done, but each will just need to be run on their own separate irrigation zones.

      • A garden tap is an excellent place to connect your irrigation system. Ideally, install a connection point behind the tap (turn the water off first) so you can still use your tap to fill a bucket when you need to.

      • Even on a typical domestic system running on mains water a filter is still a good idea. In the event of a water main fault where rubbish does find it’s way down the line, a filter will protect the system from blockage and or failure. On systems operating off recycled water, like from a tank, a screen filter is mandatory. Debris like silt & dirt from recycled water is the most common cause of blockages of failures in irrigation systems.

      • No, unless you’re tapping into your water supply, a plumber isn’t required. Most domestic irrigation systems can be installed by anyone half handy.

      • Firstly, each sprinkler &/or nozzle has a specified spray radius. Secondly, sprinklers are typically designed to deliver more water at their base & progressively less the further away you get. For this reason, you want to position sprinklers so they spray to hit the base of the next sprinkler. Of course this isn’t possible all the time so in those cases, aim to spray at least 80% of the way. By doing this you will guarantee even water across your lawn or garden.

      • Each sprinkler & nozzle sprays water at different rates, but the key factor is the flow rate of your water supply. Work that out with a simple timed bucket test. From there, you can work out how much water each sprinkler you’re looking at uses & work within your flow limit. For more information, check our Product Guides.

      • Well you’re in the right place! We’ve got it all here. The first step, is drawing out a plan of your garden, to scale of course. If you need help on how to do that, you can get started right here!

      • As you install a system, it’s almost inevitable that small fragments of dirt will get into the pipe, for this reason you should always flush out the system before running it the first time. This can be done by leaving an open end at the farthest point of each irrigation zone & operating the zone for 15 or so seconds to flush it out. Then plug it up & you’re good to go! This can also be said for any other times dirt may have gotten into the system (eg: further irrigation repairs or a mains water supply fault).

      • The type of nozzle all depends on how far you need to spray, each nozzle is specified by the radius it sprays & the spray arc it provides (0-360 degrees). Aim to spray to the base of the next closest sprinkler for even watering. For more information on planning, check out our Product Guides.

      • There’s no best type of sprinkler, just better sprinklers for different applications. Gear Drives are better for large areas, over 5m. Pop-Ups are ideal for 1.5-5m & Micro sprays are excellent for anything under that.

      • We get any number of calls from people across the country who've bought from overseas & have problems. From electrical output problems to thread compatibility problems & other problems that we aren't able to help with!

        By buying from SunshowerOnline, right here in Australia, you can be sure that your warranty issues are covered, that compatibility & compliance isn't an issue & that you'll be able to get helpful after service advice. 

      Write a review

      Please login or register to review
      • $10.96
        $13.53
        $10.96 $13.53 Ex Tax: $10.96
        • SKU: ISI-VYR26
        • Brand: Vyrsa
        • MPN: VYR-26
        • Availability: Available in 2-5 Days
        • Warranty: 12 month
      • $15.06
        $21.52
        $15.06 $21.52 Ex Tax: $15.06
        • SKU: ISI-VYR262525
        • Brand: Vyrsa
        • MPN: VYR-26+V26N-2.5+V26N-2.5
        • Availability: Available in 2-5 Days
        • Warranty: 12 month
      • $15.06
        $21.52
        $15.06 $21.52 Ex Tax: $15.06
        • SKU: ISI-VYR262825
        • Brand: Vyrsa
        • MPN: VYR-26+V26N-2.8+V26N-2.5
        • Availability: Available in 2-5 Days
        • Warranty: 12 month
      • $15.06
        $21.52
        $15.06 $21.52 Ex Tax: $15.06
        • SKU: ISI-VYR263025
        • Brand: Vyrsa
        • MPN: VYR-26+V26N-3.0+V26N-2.5
        • Availability: Available in 2-5 Days
        • Warranty: 12 month
      • $15.06
        $21.52
        $15.06 $21.52 Ex Tax: $15.06
        • SKU: ISI-VYR263225
        • Brand: Vyrsa
        • MPN: VYR-26+V26N-3.2+V26N-2.5
        • Availability: Available in 2-5 Days
        • Warranty: 12 month