These quality Rainbird Pressure Reducing filters are the perfect all-in-one with the 2 most important requirements of drip irrigation met in a single valve.
- Filtration: keeps out all the grit and dirt that can block up drip tube and fittings
- Pressure Reduction: regulates the pressure in the irrigation system so the drip tube operates evenly and effectively.
Pressure Regulating Filter Cap has sealing o-ring and unscrews to provide access to the filter element for easy cleaning.
- Max Inlet Pressure: 150 PSI
- Output Pressure: 30 PSI (20mm) 40 PSI (25mm)
- Filter Screen: 200 Mesh
Pressure reduction is vitally important for drip irrigation systems. Without a pressure reducer on your line, fittings will blow out, drippers will not flow evenly and the drip tube will not be able to distribute the water efficiently
This Pressure Reducer is not rated for mains pressure and must be installed after a Solenoid Valve or Tap Timer. Only Brass Pressure Reducing Valves can withstand mains pressure.
|Rainbird Pressure Reducer and Filter 20mm||Rainbird Pressure Reducer and Filter 25mm|
|Type||Pressure Reducing Filter||Pressure Reducing Filter|
|Inlet Thread Size||20mm BSPM||25mm BSPM|
|Outlet Thread Size||20mm BSPM||25mm BSPM|
|Min. Inlet Flow (Lpm)||0.8||11|
|Max. Inlet Flow (Lpm)||19||57|
|Max. Inlet Pressure (kPa)||1030||1030|
|Min. Recommended Pressure (kPa)||140||140|
|Max. Pressure Output (kPa)||210||280|
|Filter Type||200 Mesh||200 Mesh|
Are there any safety standards my irrigation system must meet?
The main safety concern is regarding the water supply. To avoid contamination of the mains water upstream, in most municipalities, a Dual Check Valve is required at the water connection.
Can I have drip tube & sprinklers on the same irrigation zone?
We definitely don’t recommend it. Typically, drip tube will deliver the water at a far slower rate that sprays. Because of this, if you were to have both on the same zone, the areas with drip would be left far drier than the areas with sprinkler coverage. If you do want to water some areas with drip & some with sprinklers, it can be done, but each will just need to be run on their own separate irrigation zones.
Can I just punch extra holes into my drip tube?
No, drip tube isn’t simply holes punched into poly pipe. Inside each hole is an intricate dripper which delivers that water nice and evenly. Punching a hole will simply create an uncontrolled leak!
Can I run an irrigation system off a regular garden tap?
A garden tap is an excellent place to connect your irrigation system. Ideally, install a connection point behind the tap (turn the water off first) so you can still use your tap to fill a bucket when you need to.
Do I need a filter on my irrigation system?
Even on a typical domestic system running on mains water a filter is still a good idea. In the event of a water main fault where rubbish does find it’s way down the line, a filter will protect the system from blockage and or failure. On systems operating off recycled water, like from a tank, a screen filter is mandatory. Debris like silt & dirt from recycled water is the most common cause of blockages of failures in irrigation systems.
Do I need a plumber to install or fix my system?
No, unless you’re tapping into your water supply, a plumber isn’t required. Most domestic irrigation systems can be installed by anyone half handy.
How many sprinklers can I have on a single irrigation zone?
Each sprinkler & nozzle sprays water at different rates, but the key factor is the flow rate of your water supply. Work that out with a simple timed bucket test. From there, you can work out how much water each sprinkler you’re looking at uses & work within your flow limit. For more information, check our Product Guides.
I want to design & install an irrigation system. Where do I start?
Well you’re in the right place! We’ve got it all here. The first step, is drawing out a plan of your garden, to scale of course. We’ve got Grid Paper in our Product Guides & all the advice you’ll need in there too!
Should I flush my watering system before running it?
As you install a system, it’s almost inevitable that small fragments of dirt will get into the pipe, for this reason you should always flush out the system before running it the first time. This can be done by leaving an open end at the farthest point of each irrigation zone & operating the zone for 15 or so seconds to flush it out. Then plug it up & you’re good to go! This can also be said for any other times dirt may have gotten into the system (eg: further irrigation repairs or a mains water supply fault).
What’s the best type of sprinkler for my garden?
There’s no best type of sprinkler, just better sprinklers for different applications. Gear Drives are better for large areas, over 5m. Pop-Ups are ideal for 1.5-5m & Micro sprays are excellent for anything under that.
Why do my irrigation parts keep blowing apart?
The main cause of blowout is pressure. Whether it’s poly fittings, PVC fittings or timers, whatever the component, if the pressure is too high for what it’s designed for, kaboom! Simply solve the problem with a pressure reducer & make it a brass one if it’s on your water supply.
Why should I buy from an Australian website?
We get any number of calls from people across the country who've bought from overseas & have problems. From electrical output problems to thread compatibility problems & other problems that we aren't able to help with!
By buying from SunshowerOnline, right here in Australia, you can be sure that your warranty issues are covered, that compatibility & compliance isn't an issue & that you'll be able to get helpful after service advice.
Why would I use drip tube instead of sprays?
Drip tube is excellent in areas of rich dense soil where water spreads nicely throughout. Installed under mulch, the water is delivered with minimal evaporation & wastage, going direct to the root ball.