SunshowerOnline Logo

The Vyrsa 1610 is a full circle low angle sprinkler for undertree and solid set watering systems.

  • 15mm Male BSP thread
  • Delrin – plastic construction
  • Single nozzle – 3.0mm
  • 8º Trajectory
  • Equivalent: NAAN 5024

Vyrsa 1610 Full Circle Plastic Impact Sprinkler (3.0mm nozzle)

Vyrsa 1610 Full Circle Plastic Impact Sprinkler (3.0mm Nozzle)SKU: ISI-VYR1610$13.80
$23.66

Vyrsa 1610 Full Circle Plastic Impact Sprinkler (3.0mm Nozzle)


SKU ISI-VYR1610
MPN VYR-1610
Warranty 12 month

Available in 2-5 Days

Only
$13.80

$23.66

You are hereVyrsa 1610 Full Circle Plastic Impact Sprinkler (3.0mm nozzle)

Videos

VYR S.A. Corp. eng

Specifications

Vyrsa 1610 Full Circle Plastic Impact Sprinkler (3.0mm Nozzle)
TypeFull Circle Impact Sprinkler
MaterialPlastic
ColourBlack
Inlet Thread Size15mm BSPM
Min. Flow Output (Lpm)7.1
Max. Flow Output (Lpm)10.8
Min. Recommended Pressure (kPa)150
Max. Recommended Pressure (kPa)350
Min. Spray Radius (m)11
Max. Spray Radius (m)11.5

Plastic Impact Sprinklers FAQs

What’s the best type of sprinkler for my garden?

There’s no best type of sprinkler, just better sprinklers for different applications. Gear Drives are better for large areas, over 5m. Pop-Ups are ideal for 1.5-5m & Micro sprays are excellent for anything under that.

What type of nozzles should I use?

The type of nozzle all depends on how far you need to spray, each nozzle is specified by the radius it sprays & the spray arc it provides (0-360 degrees). Aim to spray to the base of the next closest sprinkler for even watering. For more information on planning, check out our Product Guides.

How many sprinklers can I have on a single irrigation zone?

Each sprinkler & nozzle will push out water at different rates, but the key factor is the flow rate of your water supply. Work that out with a simple timed bucket test. From there, you can work out how much water each sprinkler you’re looking at uses & work within your flow limit. For more information, check our Product Guides.

Should I flush my watering system before running it?

As you install a system, it’s almost inevitable that small fragments of dirt will get into the pipe, for this reason you should always flush out the system before running it the first time. This can be done by leaving an open end at the farthest point of each irrigation zone & operating the zone for 15 or so seconds to flush it out. Then plug it up & you’re good to go! This can also be said for any other times dirt may have gotten into the system (eg: further irrigation repairs or a mains water supply fault).

Can I have drip tube & sprinklers on the same irrigation zone?

We definitely don’t recommend it. Typically, drip tube will deliver the water at a far slower rate that sprays. Because of this, if you were to have both on the same zone, the areas with drip would be left far drier than the areas with sprinkler coverage. If you do want to water some areas with drip & some with sprinklers, it can be done, but each will just need to be run on their own separate irrigation zones.

How far apart should I position my sprinklers from each other?

Firstly, each sprinkler &/or nozzle has a specified spray radius. Secondly, sprinklers are typically designed to deliver more water at their base & progressively less the further away you get. For this reason, you want to position sprinklers so they spray to hit the base of the next sprinkler. Of course this isn’t possible all the time so in those cases, aim to spray at least 80% of the way. By doing this you will guarantee even water across your lawn or garden.

Do I need a filter on my irrigation system?

Even on a typical domestic system running on mains water a filter is still a good idea. In the event of a water main fault where rubbish does find it’s way down the line, a filter will protect the system from blockage and or failure. On systems operating off recycled water, like from a tank, a screen filter is mandatory. Debris like silt & dirt from recycled water is the most common cause of blockages of failures in irrigation systems.

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Plastic Impact Sprinklers Help

Need extra help with Plastic Impact Sprinklers? Check out these resources from our Help Centre

Vyrsa 1610 Full Circle Plastic Impact Sprinkler (3.0mm nozzle)

Login

Main Menu

Powered by Verifalia email verifier